Trekking Tarp Tent - 2 person - MT900 v2 Minimal Editions - Undyed
Store Availability
Our team designed this 2-person tarp tent without poles for experienced trekkers looking for an ultralight mountain bivouacking solution.
Our bivvy style tarp tent is an ultra-light solution for experienced adventurers on multi-day trips and expeditions. Save on precious pack weight by only using your hiking poles to pitch.
BENEFITS
Easy assembly / dismantling
Requires 2 hiking poles (110/120 cm). Pre-assembled bedroom and flysheet
Easy transport
Total weight 1.3 kg. Compact & compressible 4 L cover. Dimensions 35 x12 x11 cm
Capacity
60 cm wide per person. Bedroom height 95 cm. 2 doors. 2 porches. 2 pockets
Waterproof
Water column (Schmerber): Flysheet > 2000 mm. Bedroom groundsheet > 3,000 mm
Repair
Inner bedroom and flysheet available as spare parts
Wind resistance
70km/hr (Force 8) wind resistance tested in a wind tunnel on a rotating platform
Airing
Flysheet. 2 vents for air flow. Bedroom with mosquito net
TECHNICAL INFORMATIONS
Weight
Total weight 1.3 kg
Separable parts to help transportation.
Flysheet 564 g
Bedroom 534 g
Aluminium stakes (2 pieces) 50 g
Pegs (11 pieces) 110 g
Guy ropes (3 pieces) 12 g
Bags 28 g + 15 g
To protect your product and increase your protection from the ground and bad weather, you can complement your MT900 2 person tarp tent with the MT900 groundsheet (ref.: 8797784)
Size and living space
Bedroom length 225 cm
Bedroom width 125 cm to the head and 105 cm to the feet.
Room height 95 cm
2 aluminium stakes (composed of 2 sections each) located at the feet to increase the usable space.
Two 60 cm-deep side canopies (storage space between the bedroom and flysheet), each able to accommodate a backpack of about 50 to 60 litres, mountain equipment and a pair of hiking boots.
2 pockets in bedroom.
Architecture, tent poles and tent pegs
To use this tarp tent, you need two hiking poles (ideal height 115cm; max. 120cm) to form the structure. These poles are not supplied with the tent
The pegs are made from 7075 T6 aluminium and have an extremely resistant “anvil” head.
They are non-anodised for a limited environmental impact.
This architecture makes the tent very lightweight but it needs to be fixed to the ground because it is not free-standing.
Assembly tips
Start by adjusting your poles to 115 cm in length.
Then drive the tent pegs into the ground at the four corners of the tarp tent.
Given that the flysheet and bedroom are pre-assembled, each of the poles must be slid under the flysheet, directly above each of the doors. That's how you pitch your tarp tent!
Then put the 2 aluminium stakes in the spaces provided at the foot of the tent.
Now you just have to attach the guy lines and tighten them (the height of the poles can be adjusted).
And to disassemble it
This job is very simple.
You just have to remove the 2 poles which constituted the structure of the tent, then, once the guy wires are undone and the sardines removed from the ground, to fold the tent taking into account the width of the cover.
Tip: Leave the two stakes in position to save time when you assemble it next time!
Waterproofing
Forclaz tents are laboratory-tested: pitched tent, 200 litres/sqm/hour (3 hours, equivalent to a tropical storm).
The 20D polyester (PES) flysheet (2,000 mm rating) and 40D polyamide groundsheet (3,000 mm rating) have a polyurethane coating (inside) and silicone coating (outside).
Seams taped with heat-sealed strips.
Wind resistance
We test all our tents in a wind tunnel on a turntable where we can expose each side of the tent to the wind.
To test its wind resistance, the tent must be properly pitched, taut but not stretched, with all the guy ropes in position around the tent. It should remain habitable at wind speeds of 70km/h, measured near ground level.
Our tents are certified by the CSTB independent laboratory in Nantes.
Ventilation and condensation prevention
Top ventilation on each side near the doors.
Upper part of the bedroom in mosquito net mesh to facilitate air flow.
Water repellent fabric around the outside of the bedroom to protect against condensation and draughts.
To reduce condensation inside your tent, it must be properly pitched, with the fabric kept taut without being over-stretched, and the air vents open.
Seasons
3-season tent: your tent will protect you from the harsh weather conditions you can encounter in the spring, summer or autumn. It will withstand light snowfall but is not designed to withstand heavy loads that would weigh on the structure.
In case of snow, remember to shake your tent regularly in order to bring down any snow that has accumulated to avoid putting too much weight on the structure of your tent.
Usage and care
Your tent is designed for touring bivouacs, not for static day use.
Avoid leaving it in direct sunlight as much as possible because the ultra-light fabrics can be sensitive to UV rays, which weaken them.
Repairs and After-sales service
All of our tents are designed to be repairable.
For this model, you will find in spare parts:
- the flysheet (ref 8739747)
- the inner bedroom (ref 8739744 or 8812310, greige model)
Information at your Decathlon store workshop or on the internet (decathlon.fr or https://support.decathlon.fr/)
COMPOSITION
composition
Main fabric: 20.0% Thermoplastic Polyurethane, 80.0% Polyester
Tips for storage and maintenance
DO NOT WASH.
BLEACHING EXCLUDED.
DO NOT TUMBLE DRY.
DO NOT IRON.
DO NOT DRY CLEAN.
Storage tips
After use or cleaning, do not store your tent until it is perfectly dry to prevent odours and mould forming.
TESTS AND WARRANTY
Agree by
The MT900 2P tarp tent was validated in the field under real-life conditions. It was used for 5 weeks during the spring of 2021, by 2 teams of testers, that do not belong to Decathlon, who trekked and bivouacked in the French Alps. One of the testers loved it so much that he used this model to complete his own GTA ("Grande Traversée des Alpes"). He came back delighted!
Parts guarantee
5 years. All our tents are repairable. Parts and information in store or on our website