Men's diving wetsuit 3 mm neoprene SCD 900 turquin and overseas blue
Store Availability
Store availability
BENEFITS
Easy dressing
One-piece diving suit with back zip.
Thermal insulation
3 mm full-body diving suit, watertight seams (GBS) and smooth cuffs.
Freedom of movement
Stretch neoprene and fitted cut with no underarm seams.
Robustness
Printed reinforcements on the knees to reduce wear.
Carrying comfort
Shoulder and lower back reinforcements for more comfort when carrying a tank.
Instructions
Download it hereTECHNICAL INFORMATIONS
Details of thermal insulation
3 mm full-body one-piece wet type with back zip. Seams taped using a GBS (glued and blind stitched) assembly. Once a thin layer of water (that enters through the zip) gets trapped between your body and the diving suit, the water stays warm as it is not replaced. This thin layer of water keeps you warm.
Rolled, smooth-edged cuffs, ankles and neck for maximum watertight seal.
GBS (glued and blind stitched) assembly
The diving suit's GBS assembly (Glued and Blind-Stitched) means that the seams are waterproof: the neoprene is glued first of all, then sewn for maximum strength (the sewing needle does not go completely through the neoprene in order to prevent water infiltration).
More comfort when carrying diving equipment.
A diving suit specially developed for greater comfort when carrying a diving tank and wearing a buoyancy compensator.
The neoprene reinforcements are strategically positioned at the points of the BC exposed to pressure. 5 mm more neoprene on the shoulders, the collar bones and the lumbar region that acts like a cushion.
Snap hook on the upper thigh to attach accessories.
Reinforcements to reduce wear
The diving suit has printed reinforcements on the knees to reduce wear. There are also prints on the friction zones linked to the buoyancy compensator (shoulders and lower back). Also provides better body support and prevents the vest from slipping on the slides.
Freedom of movement / Easy to put on
One-piece with stretch neoprene side panels (very soft and stretchy neoprene) to adapt to fit different body shapes and suit various physiques.
The extremities of the legs and arms are also made of stretch neoprene for easier dressing.
No underarm seams for easier arm movements.
Why use a 3 mm diving suit?
Even in warm waters, the body ends up cooling down (25 times faster than in the air). Use a thin 3 mm diving suit that will allow you to delay this drop in temperature so that you can enjoy your activity for longer. In addition, use a full-body diving suit to fully protect you from UV rays and the underwater (coral, etc.).
Thermal performance class
This scuba diving suit provides thermal protection that has been tested by the independent INPP institute (Marseille, France) in order to validate its compliance with the current standard (EN 14225-1:2017).
This diving suit is certified for use in waters warmer than 25°C.
What is a diving wetsuit?
This is the most common type of diving suit on the market. It is not designed to keep the water out, but to trap it, so that your body then warms it up, creating a thermal buffer between you and the outside.
Made of neoprene - a rubber polymer filled with air bubbles - these diving suits are available in thicknesses of 0.5 mm to 7 mm.
Thanks to their suppleness and modularity, they constitute excellent diving suits.
Tips on how to get into a diving suit?
Put your foot in a plastic bag. Then put your leg into your diving suit. Your foot comes out completely and smoothly! To adjust, ask someone to blow into your sleeve from the wrist. The incoming air inflates the interior of the neoprene diving suit, immediately separating it from your skin. You can then easily proceed with the final adjustments.
Tips on how to take care of your diving suit
1) Soak the inside and the outside of the diving suit in clean water after each session. 2) Clean with a bactericide solution. 3) Rinse thoroughly in clean water. 4) Dry on a wide hanger in a dark and well ventilated place. Pay attention to the sun, because it will cause the textile parts of the diving suit to fade. Zips can be cleaned with a toothbrush and lubricated with a suitable lubricant, such as silicone grease.
COMPOSITION
composition
Foam: 100.0% Rubber; Lining: 100.0% Polyamide
Tips for storage and maintenance
HAND WASH. MAXIMUM TEMPERATURE OF 40°C.
BLEACHING EXCLUDED.
DO NOT TUMBLE DRY.
DO NOT IRON.
DO NOT DRY CLEAN.
Storage tips
Dry your diving suit out of the sun and well clear of all sources of heat. Store your diving suit on a hanger to keep its shape and conserve the neoprene.
Restrictions on use
Not advised for swimming or wave sports.
TESTS AND WARRANTY
Test product
Designed and tested by our teams and our technical partner in Hendaye (France) to approve the thermal insulation.
Warranty
2 Years
Agree by
Our technical partner: Ocean (the PADI 5-star diving centre) based on the Water Sports Centre by DECATHLON in Hendaye - France. The centre uses SUBEA diving equipment throughout the year. The team of instructors are rigorously involved in the development of our SUBEA products: from the design phase with the teams (product managers, designers and engineers), to the endurance tests with the help of the centre’s divers (from beginners to trainee instructors, all year long).
product.ecodesign.title.tag
With ecodesign, we reduce the environmental impact of our products.
Analysing the product's environmental footprint enabled us to identify the most impactful stages of its life cycle. Thanks to this approach, our design teams were able to develop this product while significantly reducing its environmental impact.
Ecodesign actions on this product
-
Long lastingRepairability
Product has been designed to be repairable on >80% of breakages
Repairability is the ability to offer a solution in the event of product breakage or failure. The repairability of a product is defined according to 4 criteria: - The availability of instructions on how to repair the product for customers - The possibility of disassembling the product - The availability of spare parts - The price of the repair is lower than purchasing a new product Our goal is to cover any possible known break or repair a product might have. We think about the life span of a product from the design stage, to ensure that it lasts as long as possible.